Marktpreise für Commodities in Zentral- und Osteuropa

Hier finden Sie jede Woche die Marktpreise für verschiedene Typen von LDPE, HDPE und PP, die unser Partner myCEPPI in den Ländern Mittel- und Osteuropas regelmäßig erhebt. plasticker veröffentlicht wöchentlich Preisdaten mit einer Verzögerung von zwei Wochen.

Wenn Sie an aktuelleren Informationen interessiert sind, klicken Sie bitte hier für einen kostenlosen Test von "myCEPPI’s Weekly Commodity Price Report"!

Preise für KW 21/2017
(veröffenlicht von myCEPPI am 29.05.2017)

Typ Preis Diff. zur Vorwoche
PE-HD Blasware 1.243 €/t -1 €/t
PE-HD Folienware 1.230 €/t 0 €/t
PE-HD Spritzguss 1.236 €/t 0 €/t
PE-HD Rohrware (100) 1.353 €/t 0 €/t
PE-LD Folienware 1.319 €/t -3 €/t
PE-LD 1.314 €/t -6 €/t
LLDPE C4 1.228 €/t 0 €/t
PP-Copo Spritzguss 1.281 €/t 0 €/t
PP-Homo Faser 1.193 €/t -3 €/t
PP-Homo Spritzguss 1.202 €/t -5 €/t
PPR 1.337 €/t 0 €/t
GPPS 1.298 €/t 0 €/t
HIPS 1.360 €/t 0 €/t
EPS 1.330 €/t 0 €/t

29.05.2017, nur in Englisch verfügbar

Dropping PO and increasing PS prices in June

The following factors influenced “commodity” polymer prices and price expectations last week:

  • polyolefin converters expect a further price drop in June,
  • PS producers expect an increasing price tendency in June both in case of polymer and monomer grades,
  • balanced supply,
  • converters have still reduced the level of their purchases,
  • stable BRENT oil price higher than 52 USD/barrel
  • EUR/USD exchange rate over 1.1 getting stronger

In detail

Silent May is slowly over. Polyolefin converters expect a further price drop. Thus they try to keep waiting. Some polymer producers try stimulating the market by major price drops in case of smaller quantities. But this was successful only when the price offered reached the price expected by June, which is by 20-40 € lower than the prices early May.

But in case of PS the steep price drops will result, as mentioned in the previous reports, in a quick price turnaround. Some polymer producers do not take orders for May since as early as early last week. They expect a price increase by 50-100 € in case of SM and similar polymer grades.

Also polyolefin producers expect a summer price turnaround, in July but in August at latest monomer and polymer prices will start increasing. But in “low season” it is hard to pass price increases on, in this way plastic converters can get into a difficult situation again.

Polyolefin grades

But monomer prices are not yet known, both sellers and buyers expect a decrease by 20-40 EUR for June, in case of ethylene (C2) and propylene (C3) alike.

LDPE prices are eroding further. In case of the sales last week a sale price range of 1,220-1,260 was typical. Supply is good and balanced, there is a slight oversupply. Compared to the early May price level prices are by 30-50 € lower. This corresponds to the prices expected by early June. The price range expected by early June will be 1,220-1,240 €/ton. But nobody expects a major increase of the demand on the market, which will lead to a further slow price erosion until the end of June.

HDPE supply is still abundant, demand is still low. The Serbian producer has started reducing prices, in this way HDPE BM and FILM grades are available at FCA prices of 1,140 €. The typical price range in the whole region is still 1,180-1,280 €. The prices of HDPE Pipe (100) did not change, the price range is 1,350-1,450 €/ton. Early June an initial price range of 1,140-1,200 €/ton can be expected. In case of HDPE Pipe (100) prices of 1,300-1,400 € are probable.

LLDPE C4 did not drop last week, there were just low sales on the market as there is no supply. In spite of this converters expect a price drop by 30-50 € by June. The price level of mLLDPE was unchanged, within a price range of 1,350-1,360 € last week. Demand is low, a further general price drop by 30-50 € is to be expected early June.

PPH prices are still the lowest in the southern region (Serbia, Romania) here the typical price range is 1,130-1,200 €/ton, but PPH Raffia is available at an FCA price of 1,100 €/ton. Pricing of June in the end of May prices has started. Supply is good, there is a slight oversupply. By June a further price drop by 20-40 € is probable. The price of PPH IM grades is expected to be 1,100-1,150 €/ton early June, while the price range of PPH Raffia grades will be 1,090-1,130 €/ton.

PPC prices have eroded as well. There were just low sales on the market, prices were on the average by 10-20 EUR lower than last week. The typical price range is 1,220-1,300 € in the region. Early June the expected price range will be 1,200-1,270 €/ton. But nobody expects a major increase of the demand.

PPR supply and prices are stable, we did not measure major changes. The typical price range is: 1,280-1,360 €, depending on the grade. By June an average price drop by 0 € is to be expected. In this way converters try postponing their purchases to June.

On the polyolefin market price drop seems to be clear, but the extent of it will ultimately depend on the change of monomer prices. Last week market players shared the same opinion: monomer and polymer price drop by 20-40 €. However in case demand will not become more dynamic, then in June a further price reduction is to be expected corresponding to dropping margin at polymer producers.

The prices of the last week and expectations for early June are presented in the table below (full truck load, 20-22,5 t tones):
Grade name Polymer price ranges in May, 2017, Central Europe (€/ton)Expected polymer price ranges in June, 2017, Central Europe (€/ton)
HDPE blow molding 1,140-1,2601,120-1,240
HDPE film 1,140-1,2501,120-1,240
HDPE injection molding 1,170-1,2801,150-1,250
HDPE pipe (100) 1,350-1,4301,320-1,400
LDPE film 1,220-1,3801,200-1,330
LDPE general purpose 1,220-1,3901,200-1,330
LLDPE C4 1,190-1,2601,160-1,200
PP co-polymer injection molding 1,230-1,3401,200-1,310
PP homo-polymer fiber 1,120-1,2201,090-1,200
PP homo-polymer injection molding 1,140-1,2301,100-1,200
PPR 1,280-1,3601,250-1,330
GPPS 1,250-1,3201,350-1,450
HIPS 1,350-1,4001,450-1,500
EPS 1,290-1,3501,350-1,450

Polystyrene grades

Prices seem to make a turn. Styrene monomer spot prices started increasing again. Last week polymer producers and traders have forecast already June price increases both for monomers and polymers. The situation is weird, because general mood one week ago hinted to price drop in June. But last week there was a sudden turn on the monomer market. In this way SM price expectations for June turned to an increase by +50-100 €.

In case of EPS the typical price range is 1,290-1,350 € in Central Europe. But we saw also significantly cheaper EPS prices at about 1,200 €, from WE source, in reduced quantity. Based on the situation last week the expected price range will be 1,350-1,400 € early June.

However GPPS prices have eroded further last week, sales were typically made within a price range of 1,220-1,250-1,300 €. The market will almost certainly not accept the expected monomer price range, in this way polymer producers will be forced to make a margin sacrifice. In June the typical price range will be 1,250-1,320 €.

In case of HIPS demand is good and supply is stable. Prices are stable, the typical price range is 1,350-1,400 €/ton. A polymer price increase corresponding to the extent of monomer price increase is to be expected. The expected price range will be 1,400-1,470 € early June in Central Europe.

On the PS market a very high volatility lasting since 8 months has been shocking converters. They have an ever decreasing time to adapt to the changes. As a result of the sudden changes plastic converters will close an economically and financially difficult year that can result in the further drop of the demand.

Contact to myCEPPI:

László Büdy

About MyCeppi

"myCEPPI – a new voice and new approach on the plastics industry consulting and business intelligence market. With our expert advice, you can get a detailed, up-to-date and tailor-made picture of the Central and Eastern European plastics market and its main trends, data, news and key players.

Our services rely on our personal, regular and in-depth relations with players of the CEE plastics industry.

Each month, we conduct hundreds of interviews and telephone calls with industry players – plastics converters, traders, resin manufacturers – and we are also present at the biggest regional plastics trade fairs and conferences.

The information we collect in the process forms the basis of our weekly price report and market analysis; it feeds into our plastics industry company database; and it serves as the starting point for our multi-level consulting services for companies that need help sizing up, entering or navigating a specific market.

Our experts possess decades of plastics industry experience, as well as fluency in several regional languages.

Our partners include
  • key players of the CEE plastics industry – the resin
  • master-batch and machinery manufacturers
  • distributors, and plastics converters that shape market trends across the region.

We would be happy to welcome you as a partner; please do not hesitate to contact us!"

(László Büdy, Managing director, head of consulting)

Ältere Notierungen:

2017:20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
2016: 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2
2015: 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22

Woche 1/2017

PE-HD Blasware 1.224 €/t
PE-HD Folienware 1.225 €/t
PE-HD Spritzguss 1.226 €/t
PE-HD Rohrware (100) 1.267 €/t
PE-LD Folienware 1.252 €/t
PE-LD 1.255 €/t
PP-Copo Spritzguss 1.134 €/t
PP-Homo Faser 1.052 €/t
PP-Homo Spritzguss 1.042 €/t
PPR 1.247 €/t
GPPS 1.371 €/t
HIPS 1.398 €/t
EPS 1.405 €/t

Aktuelle Rohstoffpreise
Preise von Angeboten
in der Rohstoffbörse
PET Mahlgut [€/kg]
plasticker Newsletter
Wir informieren Sie schnell, umfassend und kostenlos über das, was in der Branche passiert.

Jetzt anmelden!

Jetzt Kosten im Einkauf senken!
Neuware-Restmengen, Regranulate oder Mahlgüter für Ihre Produktion erhalten Sie in der Rohstoffbörse.

Neue und gebrauchte Maschinen & Anlagen finden Sie in der großen Maschinenbörse.

Kostenfreie Nutzung aller Börsen! Registrieren Sie sich jetzt!

Neue Fachbücher
Robust Process Development and Scientific Molding – Theory and Practice

Das Buch "Robust Process Development and Scientific Molding – Theory and Practice" bietet eine Einführung in Scientific Molding und Scientific Processing für den Spritzgießprozess. [mehr]

Die neuesten Stellenangebote
Benötigen Sie für Ihre Produkte und Dienstleistungen Vertriebspartner im In- und Ausland?
Oder können Sie selbst eine Vertretung anbieten?
Hier finden Sie das optimale Umfeld!

4 Anfragen von Unternehmen
1 Anfragen von Handelsvertretern

Eigene Anfragen kostenfrei inserieren

Deutsches Kunststoff Museum
Das Exponat des Tages