Maschinen und Anlagen für die Kunststoffindustrie

Sidel Stretch Blow Moulding Machine
Angebot vom:10.06.2021
Rubrik:Blasformanlagen
Hersteller/Typ:SBO6/10
Preis:k.A.
Technische Daten:
Baujahr: 1994
Leistung: 200,0 kW
Fotos:
Beschreibung:
Sidel Stretch Blow Moulding Machine
Max. output: 6.000 bottles/hour.
Max. bottle size: 3.000 cc.
Blow stations: 6.

Machine is in very good conditioning and well maintained.

GENERAL INFORMATION
The SBO 6/10 has 6 molds and 10 heating modules.
Willwork with a wide range of bottle sizes and styles from 0.25 to 3 liters.
Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be
supplied to the machine. Separating the bottle manufacturing and preform manufacturing
processes allow production to be optimized, provide greater flexibility of operation and
use, and provide higher production output rates and yield.

MAXIMUM PREFORM DIMENSIONS
Neck height 9 – 41 mm (measured from bottom of support ring)
Minimum inside diameter of neck 19 mm
Maximum outside diameter of neck 34 mm
Preform support ring diameter 29 – 51 mm
Maximum preform length 210 mm

MAXIMUM BOTTLE DIMENSIONS
Maximum bottle diameter 130 mm
Maximum bottle height 380 mm
Bottle capacity 0.25 – 3 liters

AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids)
0.25 liter bottle 14-20 grams
0.50 liter bottle 20-33 grams
1.00 liter bottle 26-40 grams
1.50 liter bottle 35-51 grams
2.00 liter bottle 44-58 grams
3.00 liter bottle 68-84 grams

SBO 6/10 SPECIFICATIONS:
BLOW WHEEL
Height 3.5 meters
Number of molds 6
Closing force 10 tons
Item height (under neck) at outfeed 1.4 meters approximately
Machine DC drive motor power 4 KW
HEAT CONDITIONING
Height 2 meters
Number of oven heating units 10
Number of heating zones per unit 8
Maximum power 170 KW

ELECTRICAL USAGE
Maximum supplied power 200 KW
Average consumption 100-150 KW/hr (varies per bottle being produced)

COMPRESSED AIR
Supplied power from 7-35 bar
Pressure 7 bar
Flow rate 50-100 Nm3/hr (varies per bottle being produced)
Blow pressure – champagne base up to 25 bar
Blow flow rate – champagne base 110-550 Nm3/hr
Blow pressure – petaloid base up to 35 bar
Blow flow rate – petaloid base 155-770 Nm3/hr

CHILLED WATER
Temperature 10-12 degrees Centigrade
Pressure 5-6 bar
Flow rate up to 6 cubic meters/hour
Kcal to be removed up to 16,000 Kcal/hour

WEIGHT
Blow wheel with molds 8 tons
Heat conditioning unit 2.2 tons
Preform feeder 0.65 tons
Electrical cabinet 0.85 tons
OVERALL DIMENSIONS (including open gate access etc)
Length not including preform feeder 4.0 meters (157 inches)
Length including preform feeder 9.3 meters (336 inches)
Width 6.4 meters (252 inches)

DESCRIPTION AND OPERATION OF SIDEL SBO 6/10 STRETCH BLOW MOLDERS
PREFORM FEEDER
The preforms are held under the support ring by two rails before being lowered by gravity
to the feeder plate.

PREFORM HEAT CONDITONING
The preforms are transferred neck up to the heat conditioning device. This unit
continuously insures the preforms are inverted before passing, neck down, in front of the
heating units and then inverts them again. During the heating phase, the preforms are
rotated and their necks protected from the heat in order to optimize the distribution of
heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can
accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The
heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in
order to optimize the heat profile. These zones are regulated on all SBO Models. After
heating, a control by infra-red camera of preform temperature enables regulation of the
zones under control, thus insuring maintenance of the required temperature.

PREFORM TRANSFER
At the outfeed of the heat conditioning unit the preforms are transferred to the blow
wheel by means of a transfer wheel.

BOTTLE STRETCH-BLOW
The blow wheel comprises of 6 molds of the pin type locking system whose opening and
closing are cam actuated. Each mold, cooled by inner circulation of chilled water, is
fitted in a mold-holding unit with integral mechanical locking. This system allows quick
change of the molds. The blow nozzle is then inserted into the neck of the preform, thus
guiding the stretching rod, which insures the preform’s axial orientation. The blow which
insures side orientation takes place in two stages: medium pressure pre blowing and high
pressure blowing thus enabling optimum distribution of bottle wall thickness. The blow
nozzle insures perfect seal whatever the blowing pressure. The blow pressure control is
integrated into the machine.

BOTTLE DISCHARGE
The bottles are discharged from the blow wheel by an outfeed wheel which transfers the
bottles on a star wheel which pushes the bottles onto the machine outfeed.

TECHNICAL ADVANTAGES OF SIDEL SBO STRETCH BLOW MOLDERS
MACHINE RELIABILITY
Robustness and long lasting service components.
Transfer and mold open/close motions are controlled by rotary kinematics and fixed cam
paths.

PROCESS RELIABILITY
Constant quality of bottle production based on the precision and repetition of stretch
motions, and automatic adjustment of camera controlled heating zones.

PRODUCTIVITY
High productivity based on synchronization of all cam actuated motions and reduced dead
times.

INTERCHANGEABLE MOLD SETS
Molds can be designed to fit the complete line of Sidel SBO stretch blow molders.

SIMPLICITY
A single motor with simple motions actuated by timing belts and gears.

VERSATILITY
Cabinet design enables easy access and fast interchange of molds and customization parts.
Settings for heating, output rate, stretching, pre-blowing, and blowing can be quickly
and independently changed. The process can be adapted to all types of preforms.

AUTOMATIC OPERATION
The main functions of startup and operation are combined on the machine integrated
control panel. The role of the operator mainly consists of checking preform loading and
output bottle quality.

BOTTLE WEIGHT REDUCTION
Optimization of material distribution based on precision of heat conditioning and stretch
motions.

STAFF SAFETY
Machine startup can only proceed with the doors closed – opening them during machine
operation triggers an immediate shutdown of the machine. Noise levels are less than 85dB.

MACHINE SAFETY
Various safety systems avoid mechanical damage to the machine. Preventative safety
systems, such as the ejection of sub-standard preforms before heat conditioning, ejection
of unblown preforms and substandard blown preforms, etc. High speed shutdown of machine
due to prevent abnormal stress levels etc.
Anbieter:

UTB Industry B.V.

Veerweg, 14
5145NS Waalwijk
 Niederlande

Kontakt: Herr Daniel Baris

Email: daniel@utb.eu

Tel.:+31 6 12434136
Mobil:+31 6 12434136
Weitere Infos zu diesem Nutzer:

Anmeldung: 10.06.2021, seitdem:
11 Einträge in der Maschinenbörse