GMB#40252 (2014) Taylor Products Bagging System Fiber Packaging Station, Incline Slat Conveyor, Bag Dump and Meter System in USA

Brand: Taylor Products

Model: Bagging System

Year: 2014

TAYLOR PRODUCTS FIBER PACKAGING STATION

Net Weigh packaging station that will receive fiber strand from a cleated belt conveyor (or other feeding

mechanism), accumulate by weight the correct amount for one bag weighment, compress and discharge

the product into a bag for closing by operator.

The process includes the operator placing the bag on a bag clamp spout. The bag is held in place by the

bag clamps while the product is metered into the weigh chamber until the correct amount of product has

been dispensed. Then the sidewalls of the chamber close, which opens the bottom of the net weigh

chamber doors, and as the product is compressed by a plunger it is also pushed down into the bag. As the

plunger retracts the bag is released.

Components include:

Weigh System will be Taylor T-4000 meter with AB PLC unit mounted in Nema 12 Enclosure

and placed on remote enclosure stand

Carbon Steel Square tubing structural framework and carbon steel contact surfaces

Wing Press feeder system will receive material from belt conveyor and distributes it with

adjustable fingers controlled by VFD system into Net Weigh chamber

Weigh mast design with single load cell for support of the net weigh bucket and compression

plunger

Powered bag support system with motor, drive and location sensors

Net weigh chamber with discharge gate and compression sidewalls

Bag spout with clamps to hold the bag in place during fill and compression

Bag support tray for support during compression

Side guide plates which hold and form bag during compression

Compression plunger system

AB Micro 1400 PLC control package with interface for in feed conveyor system

Additional Options Added:

Dual pressure regulator and valve system which will clamp bags at lower pressure when foot

switch is used and then increase to higher pressure when double palm switches are activated.

Increased Compression cylinder size and Increased Wing Press cylinder size due to material

resistance. Hopper and wings will be UHMW lined for friction reductions.

Upgrade UHMW material to electrical conductive carbon based UHMW Polyethylene for static

reduction. (Material will be Black in Color due to Carbon injection)



Carbon steel construction with acrylic enamel finish. Requires 115 V AC 60 Hz and 460 V AC 60 Hz

Compressed air must be clean and dry

Operating temperature range of 32F to 110F



INCLINE SLAT CONVEYOR

Open slatted type belt conveyor for transport of loose product from grade ( 48″) to approximate 12′

discharge height Conveyor is approximately 25′ long overall horizontal with a 30 degree incline from

inlet to discharge.

Nominal 28″ wide conveyor body open access while transporting product.

24″ wide belt

3 ” tall cleats on (12″) centers

IHP drive

Controls with VFD

With short inlet Transition

24.00in Wide X 6ft Infeed (at O deg Incline), 30deg Lower Curve, 16.5ft Discharge@ 60fpm

Conveyed Material: Load per ft of conveyor:

10 lbs Material

Conveyed: Chopped Fiber

Motor: MTR l .00HP 56C AC 230/4 60/3/ 60

Pulley,Infeed End: CROWNED FACE PLAIN, 8.0″ DIA X 1.438″ BORE X 24″W, A HUB

Pulley FF, 12.0″ DIA X 3″W 1.69″ BORE Type D HUB

Pulley, Drive: CROWNED FACE RUBBER LAGGED, 8.0″ DIA X 1.438″ BORE X 24”W, A

HUB

Belt, Non-Stock: 24in Wide 4 PLY WHITE CROSS RIGID RMVXBB LACE #20 Alligator Steel

Recess Belt Edges 3in

Cleat Height: 3 in

Cleat Centers: 12in; Corrugated Sidewalls 3in High; (14in EW)

1.0 Frame: Formed 12g Steel 13in Deep, 28in Wide

#4 Heavy Duty Supports (2) Pairs on Horizontal for 48″ TOB

(2) Pairs on Incline for Discharge of 148.6″ BOF

249.Sin OAHL

Std Infeed, Bolt On Bottom Pan,

Vertical Rails: 6 in High;

Lower Curve, Bolt On Bottom Pan,

Vertical Rails: 6 in High;

Drive: End Drive, 45 Deg

Top Mt, Right Angle Solid Shaft Gear Reducer,

lnfeed Facing, RH Side, Bolt On Bottom Pan,

Vertical Rails: 6 in High;

Paint, Steel Components: NLE Blue

3 Sided Hopper 18″L x 6″H



BAG DUMP AND METER SYSTEM

Bag dumping system to accept filled bulk bags from customer supplied lift system into a feeder

magazine that slowly meters the product to the discharge end and uses an agitator to segregate and dispense loose product into an incline conveyor for transport up to Wing Press packaging station.

Unit will have agitator at discharge end of feeder box

Cleated belt conveyor bed incorporated at bottom of feeder box

Type 1 V-Belt Guided and Cleated Conveyor

4 8.00in Wide X 6ft I Long

Conveying Speed: l-3FPM

Conveyed Material: Load per ft of conveyor: 10 1 bs Material

Conveyed: Chopped Fiber

Motor: MTR .33HP AC 230/460/3/60 Inverter Duty Motor

Belt: 48in Wide PVC 120 Cover x FS (Thermo) With# 1 Unibar Lacing with l” Tall Cleats on

6″ Centers – V Guide A section Centered and 1-1/2″ H Corrugated Side Walls

Frame: Formed V Guided 10 g x 6.625in Deep Steel

#3 Medium Duty Supports (2) Pairs on Horizontal for 48″ TOB

Bolt On Bottom Pan Full Length

Vertical Rails: 6″ High Full Length

Gearbox drives and with VFD’s drives used to control speed of flow

Discharge spout to direct product into incline conveyor.

Sensors and PLC controls as required to operate this system including a remote and local control box.

Enclosures are NEMA 12 dust tight.

Hopper and contact surfaces will be 304 stainless steel construction.

Open design grate will be supplied which will distribute weight above feed belt but not restrict flow. (

testing will determine design and need for grate )

Factory assembled ready to operate.

Carbon steel construction for structural frame and non-contacts with acrylic enamel finish.

Unit will contain controls and sensors for communication with full system.

Requires 115 V AC 60 Hz and 460 V AC 60 Hz

Compressed air must be clean and dry

Operating temperature range of 32F to 11 OF

Location: USA

Price exworks as is / where is

[Description was hidden]