Search of "austria" in Technologie-Transfer found 16 hits.

1 bis 15 von 16 News « ‹12›»
back to search
Cost saving surface pretreatment technology for optimizing gluing, coating, imprinting or painting of plastic parts and other components
01.06.2018 - An Austrian SME developed a new atmospheric cold plasma activation technology for synthetic surfaces. Compared to similar systems it saves operating costs and 30% investment costs, is easier to install in existing productions and suitable for complex surfaces. Nearly all materials (plastics, metals,...
Polyurethanes: New 3D-Modelling and Tooling Techniques
08.02.2018 - A revolutionary 3D-modelling and tooling technology has been developed by an Austrian SME. This technology is used to produce models from polyurethanes in a close contour casting process. By providing close contour casts, this company’s customers save up to 30% in labor costs and up to 40% in material...
Highly effective purging compounds for injection moulding and extrusion reducing costs and down times
31.10.2016 - An Austrian SME developed cleaning granulates for thermoplastic processing machines. Only one third of the amount of usual products is needed and they are applicable at processing temperatures of 180°C- 450°C. They decrease cleaning costs and down times and enable effective purging even at high temperature...
Thermally conductive cushioning material sought
17.08.2015 - An international manufacturer of consumer comfort products (with a European headquarters in Austria) is looking for a technology that increases the thermal conductivity of cushioning material. The inherent insulation properties of cushioning materials limit some potential new applications. Technologies...
Innovative sealing compound required to protect electronics in rough working environments
10.07.2015 - An Austrian SME is looking for a compound to protect electronic parts from extreme conditions like heat water and temperature shocks. The company offers sensors and transponders to clients in the industrial sector and needs a robust casting and/or molding compound to seal sensitive electronics. Potential...
Textile materials for the design of new fibre reinforced plastic (FRP) parts with reduced weight and/or increased stability
04.08.2014 - An Austrian SME has developed industrial knitting for fibre reinforced materials which increase stability and reduce weight of FRP parts. Costs for clients are saved. The high flexibility of the process concerning fibres materials, densities and the high drapability of the knitted textiles facilitate...
Silicone micro injection moulding process enabling new products for medical, optical, micro-electronic and other applications
07.02.2014 - An Austrian company developed the first injection moulding process of its kind which is ready for serial production of 2-component silicone micro parts < 10mg. Parts with high precision undercuts and recesses can be produced. Via the 2-component technology, assembly steps (costs/time) are saved. Applications...
3D mouldable multilayer composites for lightweight product manufacture
04.06.2013 - An Austrian SME has developed a 3D mouldable multilayer composite (sandwich). This product has an outstanding stiffness to weight ratio, even better than carbon reinforced plastics. The basic technology enables the production of extremely thin sandwich products which have a polymer foam core and allows...
Novel technology enabling maximum flexibility for mounting of/at lightweight boards
11.10.2011 - An Austrian company has developed a 3-layer structure (lightweight material + non-woven) for lightweight panels to overcome the problem of anchoring screws in such panels. The non-woven provides huge resistance to pullout. It thus makes it possible to anchor screws in lightweight boards in every location....
Innovative photonic based sensor for online identification and classification in plastic recycling
07.10.2011 - An Austrian SME has developed an innovative photonic based sensor for online identification and classification of both small flakes/impurities and larger pieces in plastic recycling. Advantages over current systems are an identification speed of up to 4 m/s, high resolution, possible band-conveyor width...
3D mouldable multilayer composites for lightweight product manufacture
03.02.2011 - An Austrian SME has developed a 3D mouldable multilayer composite (sandwich). This product has an outstanding stiffness to weight ratio, even better than carbon reinforced plastics. The basic technology enables the production of extremely thin sandwich products which have a polymer foam core and allows...
Development of industrial production process for basalt fiber reinforced polymers for construction industry
03.02.2011 - A leading Austrian producer of endless basalt fibers is looking for a partner having know how/experience in handling and fabrication of fiber reinforced polymers. The goal is to develop and implement a (pultrusion) process for the production of fiber reinforced polymers based on basalt fibers to be...
Novel integrated heating element for mattresses providing constant temperature without electromagnetic waves
20.07.2010 - An Austrian industrial company, specialised in polyurethane (soft) foams, developed a novel mattress element to regulate the body temperature of the user by using an integrated temperature control. This special mattress guarantees constant heat emission and functions without energy input or external...
Novel thermal insulating wall-panels based on the principle of vacuum chambers, highly efficient and low-priced
21.10.2009 - An Austrian SME developed a novel insulating wall-panel based on the principle of self-contained vacuum chambers with various capabilities. With only about 24 mm thickness it achieves a heat transfer coefficient of about 0,005 W/m²K (exceeds the comparable standards many times). The panels can be produced...
New production process - thermoforming of synthetic bottles
08.08.2009 - An Austrian developer has designed a new production process for synthetic bottles with a filling volume up to 1500ml. The bottle consists of two thermoforming moulds with an internal joint. At the end of the production process the moulds are welded. Main advantages are: lower investment costs for the...
1 bis 15 von 16 News « ‹12›»
Current material prices
Average prices of offers
in the material exchange
PS Regrind [€/kg]
Latest entries in the buyers guide

Plastium GmbH
78730 Lauterbach, Germany

INTERNORM Kunststofftechnik GmbH
49401 Damme, Germany

Helco Kunststoffverarbeitung Helmig GmbH & Co.KG
48369 Saerbeck, Germany

PlastoNord GmbH
27612 Loxstedt, Germany

tasc4polymers GmbH
49219 Glandorf, Germany

» Enter the buyers guide

Latest Top-News